【STM32】STM32学习笔记-ADC单通道 ADC多通道(22)

发布时间：2024年01月06日

00. 目录

01. ADC简介

小容量产品是指闪存存储器容量在16K至32K字节之间的STM32F101xx、STM32F102xx和STM32F103xx微控制器。

中容量产品是指闪存存储器容量在64K至128K字节之间的STM32F101xx、STM32F102xx和STM32F103xx微控制器。

大容量产品是指闪存存储器容量在256K至512K字节之间的STM32F101xx和STM32F103xx微控制器。

互联型产品是指STM32F105xx和STM32F107xx微控制器。

12位ADC是一种逐次逼近型模拟数字转换器。它有多达18个通道，可测量16个外部和2个内部信号源。各通道的A/D转换可以单次、连

续、扫描或间断模式执行。ADC的结果可以左对齐或右对齐方式存储在16位数据寄存器中。

模拟看门狗特性允许应用程序检测输入电压是否超出用户定义的高/低阀值。

ADC的输入时钟不得超过14MHz，它是由PCLK2经分频产生。

02. ADC相关API

2.1 RCC_ADCCLKConfig

/**
  * @brief  Configures the ADC clock (ADCCLK).
  * @param  RCC_PCLK2: defines the ADC clock divider. This clock is derived from 
  *   the APB2 clock (PCLK2).
  *   This parameter can be one of the following values:
  *     @arg RCC_PCLK2_Div2: ADC clock = PCLK2/2
  *     @arg RCC_PCLK2_Div4: ADC clock = PCLK2/4
  *     @arg RCC_PCLK2_Div6: ADC clock = PCLK2/6
  *     @arg RCC_PCLK2_Div8: ADC clock = PCLK2/8
  * @retval None
  */
void RCC_ADCCLKConfig(uint32_t RCC_PCLK2)
功能:
	设置 ADC 时钟（ADCCLK）
参数:
   RCC_ADCCLKSource: 定义 ADCCLK，该时钟源自 APB2 时钟（PCLK2）  
返回值:
	无

2.2 ADC_RegularChannelConfig

/**
  * @brief  Configures for the selected ADC regular channel its corresponding
  *         rank in the sequencer and its sample time.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  ADC_Channel: the ADC channel to configure. 
  *   This parameter can be one of the following values:
  *     @arg ADC_Channel_0: ADC Channel0 selected
  *     @arg ADC_Channel_1: ADC Channel1 selected
  *     @arg ADC_Channel_2: ADC Channel2 selected
  *     @arg ADC_Channel_3: ADC Channel3 selected
  *     @arg ADC_Channel_4: ADC Channel4 selected
  *     @arg ADC_Channel_5: ADC Channel5 selected
  *     @arg ADC_Channel_6: ADC Channel6 selected
  *     @arg ADC_Channel_7: ADC Channel7 selected
  *     @arg ADC_Channel_8: ADC Channel8 selected
  *     @arg ADC_Channel_9: ADC Channel9 selected
  *     @arg ADC_Channel_10: ADC Channel10 selected
  *     @arg ADC_Channel_11: ADC Channel11 selected
  *     @arg ADC_Channel_12: ADC Channel12 selected
  *     @arg ADC_Channel_13: ADC Channel13 selected
  *     @arg ADC_Channel_14: ADC Channel14 selected
  *     @arg ADC_Channel_15: ADC Channel15 selected
  *     @arg ADC_Channel_16: ADC Channel16 selected
  *     @arg ADC_Channel_17: ADC Channel17 selected
  * @param  Rank: The rank in the regular group sequencer. This parameter must be between 1 to 16.
  * @param  ADC_SampleTime: The sample time value to be set for the selected channel. 
  *   This parameter can be one of the following values:
  *     @arg ADC_SampleTime_1Cycles5: Sample time equal to 1.5 cycles
  *     @arg ADC_SampleTime_7Cycles5: Sample time equal to 7.5 cycles
  *     @arg ADC_SampleTime_13Cycles5: Sample time equal to 13.5 cycles
  *     @arg ADC_SampleTime_28Cycles5: Sample time equal to 28.5 cycles	
  *     @arg ADC_SampleTime_41Cycles5: Sample time equal to 41.5 cycles	
  *     @arg ADC_SampleTime_55Cycles5: Sample time equal to 55.5 cycles	
  *     @arg ADC_SampleTime_71Cycles5: Sample time equal to 71.5 cycles	
  *     @arg ADC_SampleTime_239Cycles5: Sample time equal to 239.5 cycles	
  * @retval None
  */
void ADC_RegularChannelConfig(ADC_TypeDef* ADCx, uint8_t ADC_Channel, uint8_t Rank, uint8_t ADC_SampleTime)
功能:
	设置指定 ADC 的规则组通道，设置它们的转化顺序和采样时间
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2
   ADC_Channel：被设置的 ADC 通道
   Rank：规则组采样顺序。取值范围 1 到 16。
   ADC_SampleTime：指定 ADC 通道的采样时间值    
返回值:
	无

2.3 ADC_Init

/**
  * @brief  Initializes the ADCx peripheral according to the specified parameters
  *         in the ADC_InitStruct.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  ADC_InitStruct: pointer to an ADC_InitTypeDef structure that contains
  *         the configuration information for the specified ADC peripheral.
  * @retval None
  */
void ADC_Init(ADC_TypeDef* ADCx, ADC_InitTypeDef* ADC_InitStruct)
功能:
	根据 ADC_InitStruct 中指定的参数初始化外设 ADCx 的寄存器
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2
   ADC_InitStruct：指向结构 ADC_InitTypeDef 的指针，包含了指定外设 ADC 的配置信息  
返回值:
	无

2.4 ADC_InitTypeDef

/** 
  * @brief  ADC Init structure definition  
  */

typedef struct
{
  uint32_t ADC_Mode;                      /*!< Configures the ADC to operate in independent or
                                               dual mode. 
                                               This parameter can be a value of @ref ADC_mode */

  FunctionalState ADC_ScanConvMode;       /*!< Specifies whether the conversion is performed in
                                               Scan (multichannels) or Single (one channel) mode.
                                               This parameter can be set to ENABLE or DISABLE */

  FunctionalState ADC_ContinuousConvMode; /*!< Specifies whether the conversion is performed in
                                               Continuous or Single mode.
                                               This parameter can be set to ENABLE or DISABLE. */

  uint32_t ADC_ExternalTrigConv;          /*!< Defines the external trigger used to start the analog
                                               to digital conversion of regular channels. This parameter
                                               can be a value of @ref ADC_external_trigger_sources_for_regular_channels_conversion */

  uint32_t ADC_DataAlign;                 /*!< Specifies whether the ADC data alignment is left or right.
                                               This parameter can be a value of @ref ADC_data_align */

  uint8_t ADC_NbrOfChannel;               /*!< Specifies the number of ADC channels that will be converted
                                               using the sequencer for regular channel group.
                                               This parameter must range from 1 to 16. */
}ADC_InitTypeDef;

ADC_mode

/** @defgroup ADC_mode 
  * @{
  */

#define ADC_Mode_Independent                       ((uint32_t)0x00000000)
#define ADC_Mode_RegInjecSimult                    ((uint32_t)0x00010000)
#define ADC_Mode_RegSimult_AlterTrig               ((uint32_t)0x00020000)
#define ADC_Mode_InjecSimult_FastInterl            ((uint32_t)0x00030000)
#define ADC_Mode_InjecSimult_SlowInterl            ((uint32_t)0x00040000)
#define ADC_Mode_InjecSimult                       ((uint32_t)0x00050000)
#define ADC_Mode_RegSimult                         ((uint32_t)0x00060000)
#define ADC_Mode_FastInterl                        ((uint32_t)0x00070000)
#define ADC_Mode_SlowInterl                        ((uint32_t)0x00080000)
#define ADC_Mode_AlterTrig                         ((uint32_t)0x00090000)

ADC_ExternalTrigConv

/** @defgroup ADC_external_trigger_sources_for_regular_channels_conversion 
  * @{
  */

#define ADC_ExternalTrigConv_T1_CC1                ((uint32_t)0x00000000) /*!< For ADC1 and ADC2 */
#define ADC_ExternalTrigConv_T1_CC2                ((uint32_t)0x00020000) /*!< For ADC1 and ADC2 */
#define ADC_ExternalTrigConv_T2_CC2                ((uint32_t)0x00060000) /*!< For ADC1 and ADC2 */
#define ADC_ExternalTrigConv_T3_TRGO               ((uint32_t)0x00080000) /*!< For ADC1 and ADC2 */
#define ADC_ExternalTrigConv_T4_CC4                ((uint32_t)0x000A0000) /*!< For ADC1 and ADC2 */
#define ADC_ExternalTrigConv_Ext_IT11_TIM8_TRGO    ((uint32_t)0x000C0000) /*!< For ADC1 and ADC2 */

#define ADC_ExternalTrigConv_T1_CC3                ((uint32_t)0x00040000) /*!< For ADC1, ADC2 and ADC3 */
#define ADC_ExternalTrigConv_None                  ((uint32_t)0x000E0000) /*!< For ADC1, ADC2 and ADC3 */

#define ADC_ExternalTrigConv_T3_CC1                ((uint32_t)0x00000000) /*!< For ADC3 only */
#define ADC_ExternalTrigConv_T2_CC3                ((uint32_t)0x00020000) /*!< For ADC3 only */
#define ADC_ExternalTrigConv_T8_CC1                ((uint32_t)0x00060000) /*!< For ADC3 only */
#define ADC_ExternalTrigConv_T8_TRGO               ((uint32_t)0x00080000) /*!< For ADC3 only */
#define ADC_ExternalTrigConv_T5_CC1                ((uint32_t)0x000A0000) /*!< For ADC3 only */
#define ADC_ExternalTrigConv_T5_CC3                ((uint32_t)0x000C0000) /*!< For ADC3 only */

ADC_data_align

/** @defgroup ADC_data_align 
  * @{
  */

#define ADC_DataAlign_Right                        ((uint32_t)0x00000000)
#define ADC_DataAlign_Left                         ((uint32_t)0x00000800)

2.5 ADC_Cmd

/**
  * @brief  Enables or disables the specified ADC peripheral.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  NewState: new state of the ADCx peripheral.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void ADC_Cmd(ADC_TypeDef* ADCx, FunctionalState NewState)
功能:
	使能或者失能指定的 ADC
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2
   NewState：外设 ADCx 的新状态  
返回值:
	无

2.6 ADC_ResetCalibration

/**
  * @brief  Resets the selected ADC calibration registers.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval None
  */
void ADC_ResetCalibration(ADC_TypeDef* ADCx)
功能:
	重置指定的 ADC 的校准寄存器
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2 
返回值:
	无

2.7 ADC_GetResetCalibrationStatus

/**
  * @brief  Gets the selected ADC reset calibration registers status.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval The new state of ADC reset calibration registers (SET or RESET).
  */
FlagStatus ADC_GetResetCalibrationStatus(ADC_TypeDef* ADCx)
功能:
	获取 ADC 重置校准寄存器的状态
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2 
返回值:
   ADC 重置校准寄存器的新状态（SET 或者 RESET）

2.8 ADC_StartCalibration

/**
  * @brief  Starts the selected ADC calibration process.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval None
  */
void ADC_StartCalibration(ADC_TypeDef* ADCx)
功能:
	开始指定 ADC 的校准状态
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2 
返回值:
   无

2.9 ADC_GetCalibrationStatus

/**
  * @brief  Gets the selected ADC calibration status.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval The new state of ADC calibration (SET or RESET).
  */
FlagStatus ADC_GetCalibrationStatus(ADC_TypeDef* ADCx)
功能:
	获取指定 ADC 的校准程序状态
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2 
返回值:
   ADC 校准的新状态（SET 或者 RESET）

2.10 ADC_SoftwareStartConvCmd

/**
  * @brief  Enables or disables the selected ADC software start conversion .
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  NewState: new state of the selected ADC software start conversion.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void ADC_SoftwareStartConvCmd(ADC_TypeDef* ADCx, FunctionalState NewState)
功能:
	使能或者失能指定的 ADC 的软件转换启动功能
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2 
   NewState：指定 ADC 的软件转换启动新状态    
返回值:
   无

2.11 ADC_GetFlagStatus

/**
  * @brief  Checks whether the specified ADC flag is set or not.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  ADC_FLAG: specifies the flag to check. 
  *   This parameter can be one of the following values:
  *     @arg ADC_FLAG_AWD: Analog watchdog flag
  *     @arg ADC_FLAG_EOC: End of conversion flag
  *     @arg ADC_FLAG_JEOC: End of injected group conversion flag
  *     @arg ADC_FLAG_JSTRT: Start of injected group conversion flag
  *     @arg ADC_FLAG_STRT: Start of regular group conversion flag
  * @retval The new state of ADC_FLAG (SET or RESET).
  */
FlagStatus ADC_GetFlagStatus(ADC_TypeDef* ADCx, uint8_t ADC_FLAG)
功能:
	检查制定 ADC 标志位置 1 与否
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2 
   ADC_FLAG：指定需检查的标志位    
返回值:
   ADC状态（SET 或者 RESET）

2.12 ADC_GetConversionValue

/**
  * @brief  Returns the last ADCx conversion result data for regular channel.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval The Data conversion value.
  */
uint16_t ADC_GetConversionValue(ADC_TypeDef* ADCx)
功能:
	返回最近一次 ADCx 规则组的转换结果
参数:
   ADCx：x 可以是 1 或者 2 来选择 ADC 外设 ADC1 或 ADC2   
返回值:
   转换结果

03. ADC单通道接线图

在这里插入图片描述

04. ADC单通道示例

单次转换，非扫描模式

adc.h

#ifndef __ADC_H__
#define __ADC_H__

#include "stm32f10x.h"                  // Device header

void adc_init(void);

uint16_t adc_getvalue(void);


#endif /*__ADC_H__*/

adc.c

#include "adc.h"

void adc_init(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	ADC_InitTypeDef ADC_InitStruct;
	
	//开启ADC时钟  PA0 --> ADC1_0
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	
	//开启GPIOA的时钟
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
	
	//设置为6分频  72M / 6 = 12M 
	RCC_ADCCLKConfig(RCC_PCLK2_Div6);
	
	
	//GPIO配置 
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
	GPIO_InitStructure.GPIO_Speed =   GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStructure);
	
	//ADC配置
	ADC_InitStruct.ADC_ContinuousConvMode = DISABLE;
	ADC_InitStruct.ADC_ScanConvMode = DISABLE;
	ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStruct.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
	ADC_InitStruct.ADC_Mode = ADC_Mode_Independent;
	ADC_InitStruct.ADC_NbrOfChannel = 1;
	ADC_Init(ADC1, &ADC_InitStruct);
	
	ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_55Cycles5);
	
	//使能ADC
	ADC_Cmd(ADC1, ENABLE);
	
	//校准ADC
	ADC_ResetCalibration(ADC1);
	while(ADC_GetResetCalibrationStatus(ADC1));
	
	ADC_StartCalibration(ADC1);
	while(ADC_GetCalibrationStatus(ADC1));
	
}

uint16_t adc_getvalue(void)
{
	ADC_SoftwareStartConvCmd(ADC1, ENABLE);
	
	while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) != SET);
	
	return ADC_GetConversionValue(ADC1);
}

main.c

#include "stm32f10x.h"

#include "delay.h"
#include "oled.h"
#include "adc.h"


 int main(void)
 {	

	 uint16_t value = 0;
	 float volate = 0;
	 
	 //初始化
	 OLED_Init();
	 adc_init();

	 //显示字符串
	 OLED_ShowString(1, 1, "ADCValue: ");
	 OLED_ShowString(2, 1, "Volate:0.00V");
	 
	 while(1)
	 {
		 value = adc_getvalue();
		 volate = (float)value / 4095 * 3.3;
		 
		 OLED_ShowNum(1, 10, value, 4);
		 OLED_ShowNum(2, 8, volate, 1);		 
		 OLED_ShowNum(2, 10, (uint16_t)(volate * 100) % 100, 2);	
		 
		 delay_ms(100);
	 }
	 
 }

连续转换，非扫描模式

adc.h

#ifndef __ADC_H__
#define __ADC_H__

#include "stm32f10x.h"                  // Device header

void adc_init(void);

uint16_t adc_getvalue(void);


#endif /*__ADC_H__*/

adc.c

#include "adc.h"

void adc_init(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	ADC_InitTypeDef ADC_InitStruct;
	
	//开启ADC时钟  PA0 --> ADC1_0
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	
	//开启GPIOA的时钟
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
	
	//设置为6分频  72M / 6 = 12M 
	RCC_ADCCLKConfig(RCC_PCLK2_Div6);
	
	
	//GPIO配置 
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
	GPIO_InitStructure.GPIO_Speed =   GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStructure);
	
	//ADC配置
	ADC_InitStruct.ADC_ContinuousConvMode = ENABLE; //连续转换模式
	ADC_InitStruct.ADC_ScanConvMode = DISABLE;
	ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStruct.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
	ADC_InitStruct.ADC_Mode = ADC_Mode_Independent;
	ADC_InitStruct.ADC_NbrOfChannel = 1;
	ADC_Init(ADC1, &ADC_InitStruct);
	
	ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_55Cycles5);
	
	//使能ADC
	ADC_Cmd(ADC1, ENABLE);
	
	//校准ADC
	ADC_ResetCalibration(ADC1);
	while(ADC_GetResetCalibrationStatus(ADC1));
	
	ADC_StartCalibration(ADC1);
	while(ADC_GetCalibrationStatus(ADC1));
	
	//启动一次转换即可
	ADC_SoftwareStartConvCmd(ADC1, ENABLE);
	
}

uint16_t adc_getvalue(void)
{

	
	while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) != SET);
	
	return ADC_GetConversionValue(ADC1);
}

main.c

#include "stm32f10x.h"

#include "delay.h"
#include "oled.h"
#include "adc.h"

 int main(void)
 {	
	 uint16_t value = 0;
	 float volate = 0;
	 
	 //初始化
	 OLED_Init();
	 adc_init();

	 //显示字符串
	 OLED_ShowString(1, 1, "ADCValue: ");
	 OLED_ShowString(2, 1, "Volate:0.00V");
	 
	 while(1)
	 {
		 value = adc_getvalue();
		 volate = (float)value / 4095 * 3.3;
		 
		 OLED_ShowNum(1, 10, value, 4);
		 OLED_ShowNum(2, 8, volate, 1);		 
		 OLED_ShowNum(2, 10, (uint16_t)(volate * 100) % 100, 2);	
		 
		 delay_ms(100);
	 } 
 }

05. ADC多通道接线图

在这里插入图片描述

06. 热敏传感器

在这里插入图片描述

07. 光敏传感器

在这里插入图片描述

08. 反射式红外传感器

在这里插入图片描述

09. ADC多通道示例

adc.h

#ifndef __ADC_H__
#define __ADC_H__

#include "stm32f10x.h"                  // Device header

void adc_init(void);

uint16_t adc_getvalue(uint8_t ADC_Channel);


#endif /*__ADC_H__*/

adc.c

#include "adc.h"

void adc_init(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	ADC_InitTypeDef ADC_InitStruct;
	
	//开启ADC时钟  PA0 --> ADC1_0
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	
	//开启GPIOA的时钟
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
	
	//设置为6分频  72M / 6 = 12M 
	RCC_ADCCLKConfig(RCC_PCLK2_Div6);
	
	
	//GPIO配置 
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
	GPIO_InitStructure.GPIO_Speed =   GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStructure);
	
	//ADC配置
	ADC_InitStruct.ADC_ContinuousConvMode = DISABLE; 
	ADC_InitStruct.ADC_ScanConvMode = DISABLE;
	ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStruct.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
	ADC_InitStruct.ADC_Mode = ADC_Mode_Independent;
	ADC_InitStruct.ADC_NbrOfChannel = 1;
	ADC_Init(ADC1, &ADC_InitStruct);
	

	
	//使能ADC
	ADC_Cmd(ADC1, ENABLE);
	
	//校准ADC
	ADC_ResetCalibration(ADC1);
	while(ADC_GetResetCalibrationStatus(ADC1));
	
	ADC_StartCalibration(ADC1);
	while(ADC_GetCalibrationStatus(ADC1));
	
}

uint16_t adc_getvalue(uint8_t ADC_Channel)
{

	ADC_RegularChannelConfig(ADC1, ADC_Channel, 1, ADC_SampleTime_55Cycles5);
	
	ADC_SoftwareStartConvCmd(ADC1, ENABLE);
	
	while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) != SET);
	
	return ADC_GetConversionValue(ADC1);
}

main.c

#include "stm32f10x.h"

#include "delay.h"
#include "oled.h"
#include "adc.h"


 int main(void)
 {	

	 uint16_t ad0 = 0;
	 uint16_t ad1 = 0;
	 uint16_t ad2 = 0;
	 uint16_t ad3 = 0;
	 
	 float volate = 0;
	 
	 //初始化
	 OLED_Init();
	 adc_init();

	 //显示字符串
	 OLED_ShowString(1, 1, "AD0: ");
	 OLED_ShowString(2, 1, "AD1: ");
	 OLED_ShowString(3, 1, "AD2: ");
     OLED_ShowString(4, 1, "AD3: ");
	 
	 while(1)
	 {
		ad0 = adc_getvalue(ADC_Channel_0);
		ad1 = adc_getvalue(ADC_Channel_1);
		ad2 = adc_getvalue(ADC_Channel_2);
		ad3 = adc_getvalue(ADC_Channel_3);		 
		 
		OLED_ShowNum(1, 5, ad0, 4);
		OLED_ShowNum(2, 5, ad1, 4);
		OLED_ShowNum(3, 5, ad2, 4);
		OLED_ShowNum(4, 5, ad3, 4);		 
		 
		 
		 delay_ms(100);
	 }
	 
 }

10. 程序下载

16-ADC单通道连续转换.rar

17-ADC单通道单次转换.rar

18-ADC多通道.rar

11. 附录

参考: 【STM32】江科大STM32学习笔记汇总

文章来源:https://blog.csdn.net/u010249597/article/details/135424035
本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若内容造成侵权/违法违规/事实不符，请联系我的编程经验分享网邮箱：chenni525@qq.com进行投诉反馈，一经查实，立即删除！

【STM32】STM32学习笔记-ADC单通道 ADC多通道(22)

00. 目录

文章目录

01. ADC简介

02. ADC相关API

2.1 RCC_ADCCLKConfig

2.2 ADC_RegularChannelConfig

2.3 ADC_Init

2.4 ADC_InitTypeDef

2.5 ADC_Cmd

2.6 ADC_ResetCalibration

2.7 ADC_GetResetCalibrationStatus

2.8 ADC_StartCalibration

2.9 ADC_GetCalibrationStatus

2.10 ADC_SoftwareStartConvCmd

2.11 ADC_GetFlagStatus

2.12 ADC_GetConversionValue

03. ADC单通道接线图

04. ADC单通道示例

05. ADC多通道接线图

06. 热敏传感器

07. 光敏传感器

08. 反射式红外传感器

09. ADC多通道示例

10. 程序下载

11. 附录